An approach for measuring the FRF of machine tool structure without knowing any input force

Measuring the dynamics of a machine tool is important for improving its processing or design. In general, the dynamics of the machine tool structure is identified by the experimental modal analysis approaches that require the measurement of both the input loadings and the corresponding structural responses. However, the primary limitation for this method is that the input loadings are difficult or impossible to be measured when the machine tool is under operational conditions. In this paper, a method that is based on random decrement technology was used to identify the operational modal parameters of a machine tool without the knowledge of any of the inputs. To estimate the frequency response functions, FRFs, a structural change method was proposed. The approach is based on the sensitivity of the eigenproperties to structural modifications caused by the drive positions. The proposed method was verified experimentally by traditional hammer tests. Because no elaborate excitation equipment is used, the dynamics of the machine tool structure with arbitrarily feed rate or working position can be easily identified using the proposed active excitation modal analysis method.     

Improved error performance of a 3/4‐Sezginer space‐time block codes

The Alamouti space‐time block code (STBC) achieves full diversity gain at a rate of 1/2. However, the Alamouti scheme does not provide multiplexing gain. The Silver code offers both diversity and multiplexing gain. It has a minimum normalization determinant of . The Golden code is another STBC that offers both diversity and multiplexing gain. The Golden code is ranked higher than the Silver code because of its lower minimum normalization determinant of , however, the golden code suffers from a high detection complexity in the modulation order of M⁴. The 3/4‐Sezginer code is another STBC, which compromises between the Alamouti scheme and the Golden code in terms of diversity gain and multiplexing gain. The 3/4‐Sezginer code achieves full diversity and half of multiplexing gain. The uncoded space‐time labeling diversity (USTLD) is a recent scheme that improves the error performance when applied to the STBC in multiple‐input multiple‐output (MIMO) systems and will be applied to the 3/4‐Sezginer STBC to improve the error performance in this paper. The theoretical error probability for both the 3/4‐Sezginer STBC and the improved system is formulated using the union bound in this paper. The theoretical error probabilities of both 16‐QAM and 64‐QAM are validated through Monte Carlo simulation. The simulation and theoretical results show that the proposed system with 4 N_R can achieve an SNR gain of 1 dB for 16‐QAM and 1.2 dB 64‐QAM at a bit error rate (BER) of 10^?6.     

Torsional statics of two-dimensionally functionally graded microtubes

A size-dependent governing equation is derived to investigate the torsional static behaviors of two-dimensionally functionally graded microtubes based on the modified couple stress theory. The shear modulus is assumed to vary along the tube’s length direction according to an exponential distribute function, and varies along the tube’s radius direction according to a power-law function. A generalized differential quadrature method is developed to determine the rotational angle and shear stresses. Some illustrative examples are given to investigate the effects of applied torques, the length scale parameter and various material compositions on the torsional angle and shear stresses.     

Using a spectral scaling structured BFGS method for constrained nonlinear least squares

In this paper, we use a spectral scaled structured BFGS formula for approximating projected Hessian matrices in an exact penalty approach for solving constrained nonlinear least-squares problems. We show this spectral scaling formula has a good self-correcting property. The reported numerical results show that the use of the spectral scaling structured BFGS method outperforms the standard structured BFGS method.     

High gain observer for a class of nonlinear systems with coupled structure and sampled output measurements: application to a quadrotor

This paper proposes a new high gain observer for a class of non-uniformly observable nonlinear systems with coupled structure driven by sampled outputs. The considered class of systems is particularly constituted by several subsystems where each subsystem is associated to a subset of the output variables. The observer design is carried out through two steps. First, a high-gain observer is proposed in the continuous-time output case under the assumption that an adequate persistent excitation condition is satisfied by each subsystem. Then, the proposed observer is redesigned to handle the case of sampled outputs leading thereby to a continuous-discrete time observer. The latter property is achieved thanks to the approach pursued along the convergence analysis. The effectiveness of the proposed observer is emphasised in a realistic simulation framework involving a mathematical model of a quadrotor which is diffeomorphic to the proposed class of considered systems.     

开缝衬套挤压工艺影响TA15孔疲劳增益研究

采用对比疲劳试验方法,研究了相对挤压量、终铰参量、衬套开缝放置角度等工艺参数和特征对开缝衬套挤压TA15钛合金连接孔疲劳增益的影响。结果表明,开缝衬套挤压技术可有效提高TA15钛合金孔结构疲劳强度,延长其疲劳寿命；相对挤压量越大,孔挤压疲劳增益越大,但是TA15钛合金对挤压量非常敏感,微小的相对挤压量波动会导致显著的疲劳增益波动；在完全去除开缝衬套在孔壁遗留的材料凸脊前提下,0.190 mm和0.065 mm两种单边终铰参量对TA15孔结构挤压疲劳增益有明显影响,0.190 mm单边铰削量时挤压疲劳增益更大,而非终铰参量越小越好；在s_max=400 MPa,R=0.1疲劳载荷条件下,衬套开缝与试样最窄截面平行放置,仍能够获得明显的疲劳增益,但相对于与试样与最窄截面呈90°放置,疲劳增益会略有下降,建议在实际孔挤压操作中,衬套开缝尽量避开最窄截面放置。     

Experimental and numerical studies on the receiving gain enhancement modulated by a sub-wavelength plasma layer

A novel technique based on sub-wavelength plasma structure effects on enhancement of RF communication signals on a receiving antenna is carried out in this paper in laboratory experiments and analyzed by corresponding numerical simulations. Considerable intensification on receiving signal gain up to～10 dB in comparison with that without the plasma modulation is observed experimentally in～1 GHz RF band, with an effective enhancement bandwidth of～340 MHz and the fractional bandwidth of～34％. Then, the optimal modulation parameters of plasma are further studied by a numerical simulation. It is shown that the number density, the layer thickness, and the collision frequency of the plasma, as well as the relative distance between the plasma layer and antenna synergistically affect the modulation. Compared to the metallic antenna with the same overall dimension, the modulated antenna covered by the subwavelength plasma structure features higher receiving efficiency and lower radar cross section in the studied RF band. The mechanism of the reception enhancement is further revealed by analyzing characteristics of electromagnetic scattering and electric field distribution in the subwavelength plasma layer. The results then exhibit scientific significance and application potential of sub-wavelength plasma modulation on compact receiving antennas with higher performance and better feature of radar stealth.     

Application of dynamical system scaling method on simple gravity-driven draining process

Scaling analysis is widely used in the design of nuclear reactor passive safety systems to ensure that the scale-down test facilities can accurately capture the important phenomena in the prototypic system. In this study, the scaling distortion of a gravity-driven draining system has been analyzed with Hierarchical Two-Tiered Scaling (H2TS) method, based on the initial static characteristic values. In the draining process, however, the key parameters may vary with respect to time, leading to a certain level of scaling distortion. To evaluate the time-dependent scaling distortion, a Dynamical System Scaling (DSS) method is applied. Through comparisons of scaling results of the two scaling methods, it is concluded that the H2TS method can effectively scale the gravity-driven draining process in different geometric sizes, if the variations in the friction factor is negligible. As the draining process slows down, accompanied by an increase in the friction factor, the distortions in water level and in discharge velocity become significant, especially at the end of the draining process in a model of relatively small geometry size. This preliminary study demonstrated the process of scaling distortion analysis using the DSS identity method, and could shed light to the scaling distortion evaluation of testing programs.